BUY ONLINE NOW!
Prices, Ordering More Info...

Home

Products

Safety Data Sheets (SDS)

News

PRICING

Technical

Training

Contact Us

Events

SIGN UP FOR AUTOMATIC NOTIFICATIONS OF WORKSHOPS AND EDISON COATINGS NEWS

PAGE LINKS

Complete Product Listing by Number

Stone Restoration Products

Lime-Based Repointing Mortars

Breathable Masonry Coatings

Stucco Restoration Products

Structural Repair Products

Crack & Joint Sealants

Weatherproofing Treatments 

Waterproof Elastomeric Coatings

Masonry Consolidants

Mineral Coatings & Stains

Epoxy Seamless Flooring

Chemical Resistant Linings & Coatings

Concrete Deck Coatings

Concrete & Masonry Adhesives

Custom Patching Compounds for Historic Terra Cotta, Limestone, Sandstone, Brownstone, Marble, Granite, Stucco & Concrete

Terra Cotta Restoration & Reglazing Products+

FLEXI-DECK 500-E

100% SOLIDS ELASTOMERIC EPOXY COATING

Edison FLEXI-DECK 500-E is a 100% solids modified epoxy elastomeric membrane/coating designed for high performance waterproofing, chemical resistance and traffic compatibility under a wide range of application and service conditions.

FLEXI-DECK 500-E features odorless application, "zero" VOC content, low viscosity and self-priming to concrete, steel, aluminum, ceramic tile*, plywood, natural stone, glass*,

vinyl tile and many other substrates. (*Note: Some glassy surfaces require use of adhesion-promoting additives.) Clear or a wide range of colors is available.

Common uses for FLEXI-DECK 500-E include:

  • PARKING DECK WATERPROOFING MEMBRANES
  • INDUSTRIAL FLOORING UNDERLAYMENT
  • MECHANICAL ROOM FLOORING NON-SLIP SURFACING
  • TANK LINING/SECONDARY CONTAINMENT

THINNING, MIXING & APPLICATION

Surface Preparation: Surfaces to be coated are best if clean and dry, and free of grease, oil, dirt and other contaminants. If product will he applied over smooth or previously coated surfaces, a test application should be performed to assure adhesion and compatibility. For specific alternate procedures for contaminated or coated surfaces, consult your Edison Coatings Representative. Detailing of cracks, joints, drains, perimeters and penetrations should be performed as stated in the FLEXI-DECK 500 installation manual.

Thinning & Mixing:FLEXI-DECK 500-E is supplied as a low viscosity, two-component, 100% solids coating. For most applications, no thinning is required. In some cases thinning may be economically advantageous, to increase product spread rate. In other cases, slight solvent addition may improve the "bite" on a bard existing coating or may improve penetration of slightly oily surfaces. Thinning should be limited to the minimum required, typically about 5 - 10% solvent addition should be sufficient. Use only compatible solvents, such as Edison FLEXI-THIN 597.

Mix ratio is nominally 1:1 resin to hardener by volume. Measure and mix consistently. Product is also available in pre-measured units, eliminating the need for field measuring measuring of components. Mix thoroughly for at least two minutes, scraping the container bottom and sides to assure complete mixing. There is no induction or waiting time required after mixing before application.

The exothermic nature of epoxy setting reactions may cause rapid temperature rise when the mixture is left massed in a bucket, resulting in high temperatures and loss of utility of the product. To maximize handling and working time, pour the mixture into shallow pans or dump and squeegee tile mixture out onto the surface to be coated within a few minutes of mixing.

TECHNICAL DATA:

Composition:

100% Solids Modified Epoxy: "0" V.O.C.

Mix Ratio:

1:1 by Volume

Viscosity:

700-2000 cps

Pot Life:

20 - 30 mins. at Room Temp.

Coverage:

80 - 100 sq. ft./gal. per coat

Film Build:

40 - 70 mils (2 coats plus anti-skid aggregate)

Elongation:

110%

Tensile Strength:

1240 psi

Apply by brush, roller, squeegee or plural component spray. Clean tools and equipment immediately after use with FLEXI-THIN 597 or Xylene. NOTE: Solvents are hazardous materials. Read and observe guidelines on their manufacturers' Material Safety Data Sheets. Do not subject to immersion for at least 5 days after application, or discoloration may result.

SAFETY

Read and observe the safety and handling guidelines as detailed in the Material Safety Data Sheets supplied with this product. Avoid skin and eye contact. Epoxy resins are potential sensitizers, although Edison Coatings, Inc. avoids the use of the most highly sensitizing BGE and CGE diluents in this product. Hardener is a Corrosive Liquid. Avoid skin and eye contact. Remove from skin immediately, in case of contact. Remove contaminated shoes and clothing immediately.

FOR COMMERCIAL & INDUSTRIAL USE ONLY.

About Edison Coatings, Inc....

Edison Coatings, Inc. Products are manufactured in the United States of America from Components Originating in the United States, Canada, Italy, Germany, Spain, France, Australia, South Africa and South Korea.
BioLime NHL 3.5 Buff is a product of Italy. BioLime NHL 2, NHL 3.5 White and NHL 5.0 are Products of France. Marfil is a Product of Spain. SILAN-TREAT 88C is produced in Germany.

Copyright 2016, Edison Coatings, Inc. All rights reserved.

 Home  Products  News

 3 Northwest Drive, Plainville, CT 06062 USA

Phone: (860) 747-2220 or (800) 341-6621

FAX: (860) 747-2280 or (866) 658-1189

E-Mail: Contact Us

 Calendar  Technical  Training  Contact Us

Society for the Preservation of Historic Cements, Inc.

Last Updated:

Thursday, December 17, 2015

EDISON COATINGS PRODUCTS ARE FOR COMMERCIAL & INDUSTRIAL USE ONLY

Rosendale natural cement logo

Visit our
Rosendale Natural Cement Products® Web Site for the latest information on Traditional Cement and Masonry Materials

LIMITS OF LIABILITY

Edison Coatings, Inc. makes no warranties, express or implied, as to the accuracy or completeness of any of the information contained herein. This publication is offered on a complimentary basis as a service to potential customers or specifiers. While every effort has been made to include complete and accurate information, based on data and information believed to be reliable, it is the sole responsibility of the user to determine its suitability for his own intended use and purposes. Nothing contained herein shall be construed as a warranty or guarantee of any product, process or any other recommendation stated herein. Edison Coatings, Inc. assumes no responsibility for advice given, results obtained, or for any damages whether incidental or consequential, which may be incurred as a direct or indirect result of the use of this information. By proceeding to use this information, user acknowledges and agrees that he is doing so at his own risk, and user indemnifies and holds Edison Coatings harmless against any liabilities, costs or expenses resulting therefrom. All product sales are further governed by the Edison Coatings, Inc. CONDITIONS OF SALE.